Home > DC Electrical > Sure Power > Battery Separator >

  1314- 200, sure power Battery Separator 12V W AUX start 200amp
battery seperator 1314-200


 
Alternative Views:


List Price: $166.03
Website
Only Price:
$98.71
Weight: 3 lb


Product Code: SP-1314-200
Qty:

  
Description
 
Click Here to learn about our Sure Power Low Price Guarantee
 

The 1314-200 (unidirectional) and 1315-200 (bidirectional) are 200A battery separator modules with an integrated relay for 12V systems. The units monitor both the main and auxiliary battery banks. If the main battery (for the 1314-200) or either battery bank (for the 1315-200) is above the connect threshold, the relay connects the two banks together. If the main battery (for the 1314-200) or either batteries (for the 1315-200) are below the disconnect threshold the unit will open the relay. The connect threshold is set to a nominal voltage of 13.2V, which would only be reached when the charging system is operating. This will cause the relay to close and the charging system can charge both banks of batteries. The disconnect voltage is set to a nominal 12.8V, which is near the full charge resting voltage of the batteries. This will cause the relay to be opened shortly after the engine is stopped, attempting to preserve 100% of the starting battery capacity for engine cranking. When the engine is started, the start signal causes the controller to check if the auxiliary battery is within about 0.85V of the main battery; if so, the relay contact is closed. Thus providing the starter system with maximum battery voltage available.

For the Technical Data Sheets 
Click Here (pdf)
Click Here 
(pdf)

Battery Separator Installation

1. Mount the Battery Separator in a convenient location near the main battery bank. Do not mount in direct engine
heat. Drill 7/32 holes for -20 self-threading screws and lock washer. For material less than 0.10 add a washer
and nut (not included).
2. Connect one end of a new wire of the proper size (see wire size chart) to the main battery terminal of the Battery
Separator.
3. Connect the opposite end of a wire installed in step #2 to the main battery positive (+) terminal.
4. Connect one end of wire of proper size (see wire size chart) to the auxiliary battery terminal of the Battery
Separator.
5. Connect the opposite end of the wire installed in step #4 to the auxiliary battery positive (+) terminal.
6. Make sure the auxiliary battery is properly grounded to the vehicle chassis.
7. Ground Connection. Connect a #14 gauge wire between chassis ground and the Battery Separator ground
terminal. This may momentarily activate the Battery Separator. This is normal.
8. Auxiliary Start Connection (optional). Automatic operation. Connect a #14 gauge wire from the start position of
the ignition switch to the Start terminal of the Battery Separator. Make this connection at the ignition switch. This
wire should only have voltage when the ignition switch is in the start position. Note: The start signal must be able
to produce at least 3V* in order to provide automatic boost, see connection diagram above for manual operation
option.
9. Lamp Connections (optional). Connect a #14 gauge wire from the Lamp terminal of the Battery Separator to one
end of an indicator lamp (250mA maximum current draw). Connect the opposite end of the lamp to the chassis
ground. This lamp will illuminate when the auxiliary start function is activated.
10. Checking the Operation: The Battery Separator should now be operational. Start the vehicle or apply a charge
to the main battery. Once the main battery rises to 13.2V* the Battery Separator should activate. Turn off the
vehicle or remove the charge to the main battery. The Battery Separator should disconnect the auxiliary battery
once the voltage on the main battery drops below 12.8V*.
11. If a model 1315-200 is used, apply a charge to the auxiliary battery. When auxiliary voltage rises above 13.2V*,
the Battery Separator should activate. Remove charging unit, the Battery Separator should open when auxiliary
battery is less than 12.8V*.
12. The auxiliary start function should activate the Battery Separator if the main battery voltage is lower than the
auxiliary battery. The start terminal must see at least 3V* to activate. The auxiliary battery must read at least
10V*.


Average Customer Review: 4.5 of 5 | Total Reviews: 14 Write a review.


  0 of 0 people found the following review helpful:
 
It works... June 9, 2014
Reviewer: Anonymous Person from Twinsburg, OH United States  
I had this part fail on my 08 class B and I received 1315 - 200 even though I ordered 1314.  It works, I'm not sure what the difference is between them.  Pretty easy to replace.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
1314- 200, sure power Battery Separator July 13, 2013
Reviewer: Anonymous Person from Viola, ID United States  
Great product, and fantastic service.  Thanks

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
sure power 1314-200 June 10, 2013
Reviewer: Denny Poston from Independence, OR United States  
This is a really good product, it fits our special needs at our facility and is easy to install.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
ordering and shipping April 28, 2013
Reviewer: Marrin Fleet from Memphis, TN United States  
I have not yet installed the battery separator.  It may be some days before I do so.  The pre-sale query made to your sales desk personnel was very friendly and informative.  The product was shipped and delivered in a timely fashion.  What more can be said?

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
Battery Separator April 27, 2013
Reviewer: Edw Marshall from Willingboro, NJ United States  
AAA

Was this review helpful to you?

View All Customer Reviews

Browse for more products in the same category as this item:

DC Electrical > Sure Power > Battery Separator